My Cart
Your Cart 0

    Your cart is empty.

  • Total (Amount) ₹0.00
Exam Details

ESE (IES) Mechanical Engineering P2 2014

Review the key details, then start the test when you are ready. You can also open the full package to see related papers.

Questions 120
Duration 180 mins
Package ESE & GATE ME - Previous Year Papers

Paper pattern & analysis

Filter this paper by subject, topic or subtopic. Every graph updates from the selected questions.

Explore previous papers
Showing all 120 questions in this paper.

Subject distribution

No subject classification is available.

Topic distribution

No topic classification is available.

Subtopic distribution

No subtopic classification is available.

Difficulty distribution

Medium 83 69.2%
Hard 19 15.8%
Easy 18 15%

Question type distribution

Multiple Choices 120 100%

Instructions

Demo Instruction

Syllabus

Sample

Sample questions from this paper

Questions are selected across the paper subjects wherever the paper contains that variety.

1
2014 · Unclassified
ESE (IES) Mechanical Engineering P2 2014
Consider the following statements in connection with thermoplastics: [1]. They are long-chain molecules held together by Vander Waals forces. [2]. They cannot be re-softened once they have set and hardened. [3]. They are highly plastic and are easy for shaping [4]. Some commercial thermoplastics are polyethylence, polystyrene and PVC. Which of the above statements are correct __________?
A
1, 2 and 3 only
B
1, 3 and 4 only
C
1, 2, 3 and 4
D
2, 3 and 4 only
2
2014 · Unclassified
ESE (IES) Mechanical Engineering P2 2014
Consider the following statements: Machine tool beds are made using grey cast iron due to:[1]. high tensile strength and ductility [2]. high compressive strength and damping property [3]. castability and low cost of production [4]. machinability and low material cost Which of the above statements are correct ___________?
A
1, 2 and 3 only
B
1, 3 and 4 only
C
2, 3 and 4 only
D
1, 2, 3 and 4
3
2014 · Unclassified
ESE (IES) Mechanical Engineering P2 2014
In hot die forging, thin layer of material all around the forging is
A
gutter space, which fills up hot gases
B
flash, the width of it is an indicator of the pressure developed in the cavity
C
cavity, which is filled with hot impurities in the material
D
coining, which indicates the quality of the forging
4
2014 · Unclassified
ESE (IES) Mechanical Engineering P2 2014
Which drill is good for inverted drilling operation?
A
Oil-hole drill
B
Taper-shank drill
C
High-helix drill
D
Straight-flute drill
5
2014 · Unclassified
ESE (IES) Mechanical Engineering P2 2014
In wire-drawing operation, the maximum reduction per pass for perfectly plastic material in ideal condition is
A
0.68
B
0.63
C
0.5
D
0.58
6
2014 · Unclassified
ESE (IES) Mechanical Engineering P2 2014
In the process of metal rolling operation, along the arc of contact in the roll gap there is a point called the neutral point, because material
A
on one side of this point, the work material is in tension and on the other side, the work material is in compression.
B
on one side of this point, the work material has velocity greater than that of the roll and on the other side, it has velocity lesser than that of the roll.
C
at this point there is no increase in material width, but on either side of neutral point, the material width increases.
D
on one side of this point, the work material has rough surface finish and on the other side, the work material has very fine finish.