Difficulty distribution
How the classified questions are distributed by difficulty.
6questions
Medium
6
100%
Geometry - General Aptitude - General Aptitude (GA) Previous Year Questions
Practice Geometry - General Aptitude - General Aptitude (GA) previous year questions organised from real papers, with year-wise coverage and clear topic navigation.
5Papers
4Years
6Questions
1Topics
Geometry question pattern
Every graph below is calculated only from this selection.
Questions by year
Year-wise coverage for Geometry. Each bar uses a separate theme-derived color.
Question type distribution
MCQ, numerical, multiple-select and other formats found in these papers.
6questions
MCQ
4
66.7%
Numerical Answer Type (NAT)
2
33.3%
Subject weightage
Top subjects by unique question coverage.
Most asked topics
Top topics across the included previous year papers.
Subtopic coverage
Top subtopics inside this exact selection.
Paper coverage
Question coverage for the most populated papers. Every active PYP paper remains listed below.
Included previous year papers
Newest papers appear first. Sort by year, question coverage or name.
| Paper | Year / session | Questions in this view | Open |
|---|---|---|---|
| Mechanical Engineering (ME) 2018 [Session 1] | 2018 | 1 | View paper |
| Mechanical Engineering (ME) 2015 [Session 1] | 2015 | 1 | View paper |
| Mechanical Engineering (ME) 2015 [Session 3] | 2015 | 1 | View paper |
| Mechanical Engineering (ME) 2014 [Session 2] | 2014 | 1 | View paper |
| Mechanical Engineering (ME) 2012 | 2012 | 2 | View paper |
All Geometry previous year questions
Practice every matching question in batches of 20, with every available option.
2012 · General Aptitude (GA) · General Aptitude · Geometry
Mechanical Engineering (ME) 2012
A solid disc of radius \(r\) rolls without slipping on a horizontal floor with angular velocity \(\omega\) and angular acceleration \(\alpha\). The magnitude of the acceleration of the point of contact on the disc is
2012 · General Aptitude (GA) · General Aptitude · Geometry
Mechanical Engineering (ME) 2012
Consider two infinitely long thin concentric tubes of circular cross section as shown in the figure. If D_1 and D_2 are the diameters of the inner and outer tubes respectively, then the view factor F_{22} is given by
2014 · General Aptitude (GA) · General Aptitude · Geometry
Mechanical Engineering (ME) 2014 [Session 2]
A 4-bar mechanism with all revolute pairs has link lengths \(l_f = 20\) mm, \(l_{in} = 40\) mm, \(l_{co} = 50\) mm and \(l_{out} = 60\) mm. The suffixes \(f\), \(in\), \(co\) and \(out\) denote the fixed link, the input link, the coupler and output link respectively. Which one of the following statements is true about the input and output links?
2015 · General Aptitude (GA) · General Aptitude · Geometry
Mechanical Engineering (ME) 2015 [Session 1]
In a slab rolling operation, the maximum thickness reduction (\(\Delta h_{max}\)) is given by \(\Delta h_{max} = \mu^2 R\), where \(R\) is the radius of the roll and \(\mu\) is the coefficient of friction between the roll and the sheet. If \(\mu = 0.1\), the maximum angle subtended by the deformation zone at the centre of the roll (bite angle in degrees) is ______
2015 · General Aptitude (GA) · General Aptitude · Geometry
Mechanical Engineering (ME) 2015 [Session 3]
A weight of 500 N is supported by two metallic ropes as shown in the figure. The values of tensions \(T_1\) and \(T_2\) are respectively
2018 · General Aptitude (GA) · General Aptitude · Geometry
Mechanical Engineering (ME) 2018 [Session 1]
